In more than 20 years of wrenching for pros and even more years as a bike shop mechanic, I’ve learned a few things about bottom bracket repair. It’s important to remember that bottom bracket squeaks have nothing to do with the age of the bike. Sometimes, even when a bike is new from the factory, the bottom bracket isn’t tight and it creaks. Other times, it's not the bottom bracket at all.

Read on to learn how to fix a creaking bottom bracket—and where the sound might actually originate.

5 Things That Sound Like a Creaking Bottom Bracket

Most surprisingly, what often sounds like a bottom bracket creak is actually something else. Most of the time, the true cause is a loose chainring bolt—tighten them up and that’ll quiet most creaks. After you check the chainring bolts and if you still hear the noise, look at your pedals, crank bolts, seatpost, and seat. By checking these first, you’ll save an hour of digging into your bottom bracket.

More From Bicycling
 
preview for HDM All Sections Playlist - Bicycling

Kill the creak from these other culprits with the following tips:

Chainring bolts: Tighten with a 5mm hex wrench and chainring nut wrench.

Pedals: Lube all the points where your cleats make contact with the pedals. Also, remove them from the crank arm with a pedal wrench, then grease the threads and reinstall.

Crank bolts: If your cranks move side to side more than 1/16 of an inch, you’ve found the likely creak source. Remove each bolt with an 8mm hex wrench or 14mm socket wrench, then grease and retighten them.

Seatpost: Remove and grease. Corrosion can form between the seatpost and frame, making a clicking sound. If an ungreased seatpost stays in the frame too long, it’ll become stuck, so make sure you do this every so often.

Seat: Tighten the seat binder bolt and grease the seat rails and clamp bolts. The seat may be far away from the bottom bracket, but the noise can transfer through the bike.

4 Great Bike Lube Options We Love
Boeshield T-9 Lubricant
Boeshield Boeshield T-9 Lubricant
Now 12% Off
$10 at Amazon
Credit: Boeshield

A light, waterproof combo of solvents, lubricants, and waxes

Phil Wood Waterproof Grease
Phil Wood Waterproof Grease
Credit: Phil Wood

The gooey, green standard for non-chain bike lube

Pedro's Chainj Chain Lube
Pedro's Chainj Chain Lube

An environmentally-friendly pick for moderate to wet conditions

Phil Wood Tenacious Oil
Phil Wood Tenacious Oil
Now 11% Off
Credit: Phil Wood

A multi-purpose lube for forks, suspension pivots, and bearings

    Bottom Bracket Repair Tips

    If you've checked the above, and you still hear a persistent creaking, it's time to work on the bottom bracket. Keep in mind, it's important to use the correct tools (as mentioned below). Trying to make do with common tools like locking pliers, slip-jaw pliers, and adjustable wrenches can end up stripping your bottom bracket and do more harm than good. Find the bracket you have, then follow the steps to fix it.

    Ball-Bearing Bottom Brackets

    Loosen the lock ring on the bottom bracket with a lock ring tool. With a pin spanner, turn the adjustable cup clockwise until there’s no more play, but no binding in the bearings. Tighten the lock ring down to set the adjustment in place. If there’s still creaking, replace the bearings. Also, inspect the race, where the ball bearings sit, for corrosion or other damage (known as "pits")—you’ll need a new bottom bracket if you find any.

      Cartridge and External Bearing Bottom Brackets

      Remove this bracket with a sealed cartridge bottom bracket tool or external bearing bottom bracket tool. Clean thoroughly, then re-grease the threads on the frame and bottom bracket. For stubborn cartridge bottom bracket squeaks, use Teflon tape on the threads. Then, reinstall, putting a drop of Green Loctite on the threads. For titanium frames, use Finish Line Ti-Prep Anti-Seize Assembly Lubricant on the threads.

      Press Fit Bottom Brackets

      Press fit bottom brackets are trickier to service. You’ll need the right removal tool, which will cost you about $40. And then you’ll need a quality bearing press tool to reinstall it, which costs anywhere from $80 to $240. Given how many times you’ll likely need to work on your bottom bracket (not often), you may be better off bringing your bike to your local bike shop. Press fit bottom brackets aren’t designed to be reused after being removed, so you’ll need a fresh one. Also, you'll need to apply press fit retaining compound before installing it, like the one from Park Tool.

      Other Bike Noises

      Chipped paint on the threads or the face where the frame and bottom bracket meet can also cause noise. To fix it, the bottom bracket should be faced with a facing tool. Or, in a pinch, remove remaining paint with a razor. Just beware, a slip of the razor means a frame gouge, and possible frame-threatening damage, so you have to be extra careful.

      You can also check to see if the noise is coming from your headset or stem by applying force to your handlebar and rocking it back and forth. If yes, disassemble both, clean, and then regrease.

      When in doubt, or if you don’t have the proper tools for the job, take your bike to your local bike shop. They'll know what to do.